246284 Hydraulic Solenoid Valve
Product Description: 246284 Hydraulic Solenoid Valve for 3-Way Directional Control Hydraulic systems need reliable valves to direct flow, shift circuits, and control actuators. The 246284 hydraulic solenoid valve from Flying Bull is a direct-acting, 3-way, spool-type directional valve designed for ordinary pressure hydraulic systems. It is an electromagnetic drive, hydraulic thread directional valve that screws directly into a standard T4-2 cavity. This 246284 solenoid valve is a 3-way, 2-position valve. Three ports mean it can direct oil from a pressure port to either of two working ports (or to tank). Two positions mean the valve has two operating states – energized (solenoid on) and de-energized (solenoid off). A spring returns the spool to the default position when power is removed. Key Technical Parameters: Maximum Working Pressure: 50 bar (for pilot/control circuits – note the valve is rated for 210 bar internal pressure sealing). Internal Leakage: less than 80 ml/min at 210 bar. Operating Voltage Options: 12VDC, 24VDC, 110VAC, 220VAC. Minimum operating voltage: 85% of rated voltage. Filtration Requirement: 20μm or better. Standard Cavity: T4-2. Standard valve block models: T4-21, T4-23, T4-24, T4-26. Temperature Range: -30°C to +100°C (nitrile rubber seals). Media: Oil. How the 246284 Hydraulic Solenoid Valve Works: This is a direct-acting spool valve. When the solenoid coil is energized, it creates a magnetic field. That magnetic force pulls the spool directly – no pilot pressure needed. The spool moves to change which ports are connected. When power is removed, a spring pushes the spool back to its original position. Direct-acting valves respond quickly (milliseconds) and work even when system pressure is very low or zero. Important Precautions When Using Threaded Cartridge Valves: Correct Sizing (Flow and Pressure): Before selecting a threaded cartridge valve, check both flow rate and pressure rating. Also study the flow-pressure curve. If you choose a valve that is too small, it will create excessive pressure loss and heat the system. If you choose a valve that is too large, you waste money on capacity you do not need. Match the valve to your actual system requirements. Seal Material Compatibility: Threaded cartridge valves use different seal materials for different fluids. Fluorine rubber (FKM/Viton) seals – Suitable for phosphate ester fluids (fire-resistant hydraulic fluids). Butyl rubber (Nitrile/NBR) seals – Suitable for mineral oil (standard hydraulic oil). Using the wrong seal material will cause swelling, hardening, or leakage. This valve comes with nitrile rubber seals for mineral oil. Pressure and Flow Setting Values: You can specify the setting value (e.g., cracking pressure for a relief valve) when ordering. If you do not specify, the manufacturer sets a default value. For the 246284 as a directional valve, the setting is typically not adjustable – verify with your supplier. Contamination Sensitivity: Threaded cartridge valves are more sensitive to contamination than plate-mounted valves. The clearances between spool and bore are very tight. A tiny piece of dirt can stick the spool. Always design the system with proper filtration (20μm or better). Flush the system thoroughly before operation. Shifting Speed: The shifting speed of a threaded cartridge solenoid valve is slightly slower than a conventional (stack) solenoid valve. For applications that require very fast action (e.g., safety circuits or high-cycle machinery), you may need a fast-response cartridge valve. Those are available but cost more. Applications for the 246284 Hydraulic Solenoid Valve: Pilot control for main hydraulic valves (remote operation of large directional valves). Shifting hydraulic circuits on construction machinery (e.g., selecting between high-speed and low-speed travel). Actuator control in industrial automation. Flying Bull’s 246284 hydraulic solenoid valve is 100% brand new, manufactured in Zhejiang, China, and backed by a 1‑year warranty. Delivery takes 5–7 working days.
Product Introduction
Products Description
Model: 246284 Hydraulic Solenoid Valve |
Media: Oil |
|
Warranty: 1 YEAR |
Condition: New, 100% Brand-new |
|
Place of Origin: Zhejiang, China |
Power: Hydraulic |
|
Brand Name: FLYING BULL |
Quality: High-Quality |
|
Delivery: 5-7 Working Days |
Pressure: Ordinary Pressure |
Technical parameters
Maximum working pressure: 50 bar
Internal leakage: <80ml/min at 210 bar
Operating voltage: 12VDC, 24VDC, 110VAC, 220VAC
Minimum operating voltage: 85% of normal voltage
Filtration accuracy: 20μm or better
Standard jack: T4-2
Use temperature: -30~+100℃ (nitrile rubber)
Standard valve block model: T4-21*/23*/24*/26*
Electromagnetic drive, 3-way, direct acting spool type, hydraulic thread direction valve.
Valve use precautions
When using hydraulic screw cartridge valves, pay attention to the following matters:
(1) When selecting a threaded cartridge valve, be sure to see its flow rate and pressure, but also pay attention to its flow pressure curve, if the selection is too small often causes the system pressure loss is too large, so that the system heating, if the selection is too large, it will cause economic waste.
(2) Thread cartridge valve sealing materials have two kinds, fluorine rubber seal is suitable for phosphoric acid medium, butyl rubber seal is suitable for mineral oil medium.
(3) For the pressure value and flow value of the threaded cartridge valve, the setting value can be specified when selecting, if not specified, the manufacturer will set a default value.
(4) Thread cartridge valve is more afraid of pollution than plate valve, in the design of the system must do a good job of filter design, and fully clean before operation;
The reversing speed of the 5-thread cartridge solenoid valve is slightly slower than that of the conventional solenoid valve, and for the occasions requiring fast action, only the fast screw cartridge solenoid valve is selected, but the price is higher.



Company Introduction







Frequently Asked Questions (FAQs)
1. What is the model number and basic specification of this hydraulic solenoid valve?
The model is 246284 hydraulic solenoid valve. It is a direct-acting, 3‑way, spool-type, hydraulic thread directional valve. Maximum working pressure is 50 bar (pilot/control circuits). It fits a standard T4‑2 cavity.
2. How does the 246284 solenoid valve work?
This is a direct-acting valve. When the solenoid coil is energized, it creates a magnetic field that pulls the spool directly (no pilot pressure). The spool moves to change which ports are connected. When power is removed, a spring returns the spool to its original position. Direct-acting valves respond quickly and work at low or zero pressure.
3. What voltage options are available for the 246284?
The valve is available in 12VDC, 24VDC, 110VAC, and 220VAC. The minimum operating voltage is 85% of the rated voltage. Using lower voltage may cause the valve to not shift fully or to chatter.
4. Why is contamination a bigger problem for cartridge valves than plate valves?
Threaded cartridge valves have very tight clearances between the spool and the bore (to minimize internal leakage). A tiny particle of dirt – as small as 20μm – can get stuck in that clearance and cause the spool to stick. Plate valves generally have larger clearances and are more tolerant of contamination. Always use 20μm or better filtration.
5. How do I choose the right seal material for my system?
Nitrile rubber (NBR) – For mineral oil (standard hydraulic oil). This valve comes with NBR seals.
Fluorine rubber (FKM/Viton) – For phosphate ester fluids (fire-resistant hydraulic fluids). Do not use FKM with mineral oil – it may harden.
Using the wrong seal material causes leakage, swelling, or seal failure. If you use special fluids, contact the supplier for custom seals.
6. Can the shifting speed of the 246284 be too slow for my application?
Threaded cartridge solenoid valves shift slightly slower than conventional (stack) solenoid valves. For most construction and industrial applications, the speed is fine. For very fast action (e.g., high-cycle presses or safety circuits), you may need a fast-response cartridge valve. Those cost more. Test your cycle time requirement before choosing.
7. What happens if I select a valve with incorrect flow or pressure rating?
If the valve is too small – It creates high pressure loss (resistance). That wastes energy, heats the oil, and reduces actuator speed.
If the valve is too large – You pay for capacity you do not need. The valve may also shift slower because of larger internal volumes. Always match the valve to your system's actual flow and pressure.
8. Does the 246284 hydraulic solenoid valve come with a warranty?
Yes. Flying Bull provides a 1‑year warranty against manufacturing defects. Damage caused by contaminated fluid (filtration below 20μm), incorrect seal selection for the fluid, wrong voltage, overpressure, or improper installation is not covered.
9. Is this valve a direct replacement for other brands using the T4‑2 cavity?
Yes. The 246284 fits the standard T4‑2 cavity (common in many hydraulic manifolds). However, always verify that the flow direction, pressure rating, and voltage match your original valve. Do not rely only on cavity size – some manufacturers use different port assignments.
10. What maintenance does the 246284 hydraulic solenoid valve require?
The valve itself requires no regular maintenance. However, change hydraulic filters on schedule. Keep oil clean and at the proper level. If the valve sticks, first check contamination. If the coil fails, measure resistance with a multimeter. Replace the valve if cleaning does not solve the problem.
Hot Tags: 246284 hydraulic solenoid valve, China 246284 hydraulic solenoid valve manufacturers, suppliers, factory, liugong solenoid valve replaced, jlg solenoid valve replaced, sandviken solenoid valve replaced, lovol solenoid valve replaced, john deere solenoid valve replaced, kubota solenoid valve replaced
You Might Also Like
Send Inquiry










